Mobile Origin Earphone Cleaning Set CL2

Aprašymas

Mobile Origin Cleaning Kit for Earphones CL2

Mobile Origin Cleaning Kit for Earphones CL2 is a cleaning kit for earphones, charging ports and other openings where dust and grease build up. The metal tin contains four cleaning tools and three blocks of cleaning compound, which pulls dirt out of speaker and microphone grilles as well as from places a brush cannot reach. It cleans mechanically, without water or chemicals, so there is no risk of short circuit or damage to electronics caused by moisture.

• Cleaning compound and four tools in one tin: everything for cleaning earphones and ports in one place, without needing any additional accessories.
• The compound reaches every crevice: it cleans AirPods grilles, USB-C ports, microphones and button openings that a brush cannot reach.
• No water or chemicals: it cleans only by adhesion of the compound, so there is no risk of short circuit or moisture damage.
• Up to 96 portioned uses: three blocks divided into small pieces last for months.
• Phthalate-free, confirmed by SGS testing: compliance with REACH (Annex XVII, items 51 and 52) is verified by testing, not just declared.

The cleaning compound pulls dust out of the grille

Earphones collect dust, grease and flakes of skin every day, which settle mainly in the speaker grille. After a few weeks, the result can be heard: bass becomes weaker, highs are muffled and maximum volume sounds only half as loud. A brush usually pushes this layer deeper in, while the cleaning compound pulls it out.

The compound works on the principle of adhesion. A small piece is pressed onto the grille, adapts to the surface and, when pulled away, takes with it the particles that have stuck to it. When used correctly, it does not run, dissolve or leave residue, so it can handle even sensitive electronics, the speaker grille of AirPods, microphone openings and charging ports.

Four tools, each for a different opening

The package contains four tools because every type of dirt and opening requires something different. The precision tip moves larger pieces of dirt away from the edges of openings. The cleaning brush loosens settled dust on the surface. The hook (probe) cleans button openings and narrow crevices, for example around the SIM slot. The nylon brush (white) is suitable for speaker and microphone grilles, where a harder brush could damage delicate fibers.

The correct order is to first loosen the dust with a tool and only then press on the compound. The tools measure 5 cm, 6 cm, 5.5 cm and 5 cm, so they can reach even deeper openings while still fitting inside the tin.

Up to 96 uses in portioned cubes

A common mistake when cleaning with compound is using too large a piece. A large piece of compound has more difficulty getting into the grille and is more likely to leave residue behind. That is why CL2 supplies the compound in the form of pre-portioned cubes, where one cube corresponds to the amount for one cleaning.

The three blocks in the package last for approximately 96 uses, so one package will last for months. The process is simple: warm one small piece between your fingers for about 10 seconds, briefly press it onto the surface and pull it straight away from the grille. The actual number of uses depends on the size of the area being cleaned; an AirPods grille uses a smaller piece than a USB-C port.

No water, no chemicals, no risk of short circuit

The compound contains no water, solvents or aggressive surfactants, so there is nothing that could short-circuit electronics or leave behind a damp residue. Cleaning is purely mechanical, by the compound adhering to the surface and being pulled away. This is especially important for more expensive devices, where cleaning with a damp cloth or spray involves a certain risk.

The Safety Data Sheet (SDS) classifies the compound as a non-hazardous substance, and SGS testing confirmed zero phthalate content according to REACH regulation.

What devices it is suitable for

The kit cleans practically anything with a grille, opening or crevice. It is suitable for in-ear earphones and AirPods, phone charging ports (USB-C and Lightning), microphones and speakers, as well as laptops, keyboards and gamepads. For keyboards and gamepads, the tools are mainly used; for earphones and ports, the combination of tool and compound is used.

Do not use the compound on displays or wet surfaces. The kit is intended for dry openings and grilles, not for surfaces where the compound could smear or trap moisture.

Specifications

• Compatibility: AirPods, earphones, USB-C, microphone
• Number of uses: up to 96
• Box dimensions: 110 × 70 × 28 mm
• Color: beige-green
• Material: phthalate-free cleaning compound, plastic, metal
• Weight: 112 g

Safety and storage

Keep the kit out of reach of children under 3 years of age. It contains small parts (choking hazard) and the cleaning compound is not intended for consumption. Store in a dry place and do not use the compound on displays or wet surfaces.

Package Contents

• 1× metal tin (110 x 70 x 28 mm)
• 1× precision tip (5 cm)
• 1× cleaning brush (5.5 cm)
• 1× hook / probe (6 cm)
• 1× nylon brush, white (5 cm)
• 3× block of cleaning compound (pre-portioned)
• User manual